Since 2004. Factory in Lishui, Zhejiang.
Duplex Pipe Fittings Manufacturer
Duplex 2205 and 2507 butt-weld fittings from HuaboPipe: elbows, tees, crosses, concentric and eccentric reducers, caps and stub ends — cold formed. Made to ASME B16.9 dimensions; also EN 10253, DIN, JIS, GB/T 12459 or drawing. Standard sizes DN15 to DN1200; larger sizes are made to drawing, up to DN3000. Wall thickness per order. EN 10204 3.1 MTRs available; EN 10204 3.2 available on request. PMI available; heat numbers traceable.
Huabo Pipe Industry Co., Ltd. (HuaboPipe): founded 2004; company in Wenzhou; factory in Lishui (No. 102 Longqing Road, Shuige Industrial Zone); warehouse in Longwan. We manufacture stainless steel butt-weld fittings and forged flanges, and can supply matching stainless pipe and valves on the same project list. For the combined fittings-and-flanges overview, see duplex 2205 / 2507 fittings and flanges. This page focuses on butt-weld fittings buying points.
Product range
| Item | Types | Notes |
|---|---|---|
| Elbows | 45°, 90°, 180° | Long or short radius per standard or drawing |
| Tees | Equal / reducing | State header and branch sizes for reducing tees |
| Crosses | Equal / reducing | Same as tees |
| Reducers | Concentric / eccentric | Eccentric: state installation orientation — see concentric vs eccentric |
| Caps | Per standard or drawing | — |
| Stub ends | For lap-joint flanges | Check with the matching flange |
| Size / wall | Standard DN15 to DN1200 | Larger to drawing, up to DN3000; wall per order |
Standards and grade marking
| Item | How to write it |
|---|---|
| Fitting dimensions | Made to ASME B16.9 dimensions; also EN 10253 (duplex: EN 10253-4), DIN, JIS, GB/T 12459 or drawing |
| 2205 | State UNS S31803 or S32205; ASTM fitting grades A815 WPS31803 / WPS32205; EN material no. 1.4462 |
| 2507 | UNS S32750; ASTM A815 WPS32750; EN 1.4410 |
| Manufacture | Seamless or welded, as on the drawing / material spec |
| Ends / wall | Match connecting pipe; state both ends for reducers and reducing tees |
S31803 and S32205 are different composition ranges — do not treat them as the same mark. Fittings usually match the connected pipe grade; do not change the grade without design approval.
Manufacturing points for duplex fittings
- Process. Material check → cut → cold form → heat treatment (solution annealing) → bevel/finish → surface treatment (polishing, pickling, sand blasting and sand tumbling) → inspect → mark and pack.
- Solution annealing. After cold work, duplex needs solution annealing and rapid cool to restore austenite/ferrite balance and limit harmful phases (e.g. sigma).
- Heat-number traceability. Incoming material and finished pieces keep furnace / heat numbers aligned with the MTR.
Field welding notes
- Weld to an approved WPS. Common fillers: 2205 → ER2209; 2507 → ER2594 (AWS A5.9) — final choice per WPS. Heat input and interpass per WPS and project rules.
- Ferrite content after welding: follow WPS and project requirements when specified.
- Dissimilar joints (e.g. duplex to 316L): whether allowed and how to weld is a design / WPS decision.
- Bevel: per standard or drawing — state it in the inquiry.
Inspection and documents
| Item | HuaboPipe practice |
|---|---|
| PMI | Available |
| Dimensional check | Per standard or drawing |
| PT, UT, hydrotest | Per order |
| Corrosion tests | Available on request |
| EN 10204 3.1 MTR | Available; heat numbers traceable |
| EN 10204 3.2 | Available on request |
| Third-party inspection | Supported within the agreed scope |
If the project needs ferrite measurement, metallography or hold points, write them in the inquiry before production starts.
Where duplex is used
Duplex is often chosen where strength and chloride resistance both matter — seawater, desalination and chloride-bearing chemical duty. HuaboPipe fittings and flanges serve petrochemical, chemical, LNG, power and water treatment projects. For 2205 vs 2507 vs 316L selection, read 316L vs duplex 2205 fittings; final grade is confirmed by design.
What to send for a quote
- Grade: 2205 (S31803 or S32205) or 2507
- Item and type (elbow angle/radius, equal/reducing tee, concentric/eccentric reducer)
- Size and wall at both ends
- Standard: ASME B16.9 dimensions, EN 10253, DIN, JIS, or drawing
- Quantity and delivery place
- NDE (PT/UT, ferrite, corrosion tests) and certificate type (3.1 / 3.2)
- If grade is open: medium, temperature and pressure
Need matching flanges? List them on the same inquiry — see duplex forged flanges. Buying flow: buying guide.
Email lucas@hbpipe.com · WhatsApp +86 152 1057 8298. We typically reply within one business day.